Fractal Design Node 304 mITX Case Review: Paving the Way to the Future
by Dustin Sklavos on November 23, 2012 12:01 AM EST- Posted in
- Cases/Cooling/PSUs
- Mini ITX
- Fractal Design
- mITX
Testing Methodology
For testing Mini-ITX cases, we use the following standardized testbed in stock and overclocked configurations to get a feel for how well the case handles heat and noise.
| Mini-ITX Test Configuration | |
| CPU |
Intel Core i3-2120 (65W TDP) |
| Motherboard | Zotac Z68ITX-A-E |
| Graphics Card |
Intel HD 2000 IGP Zotac GeForce GTS 450 Eco (dedicated) |
| Memory | 2x2GB Crucial Ballistix Smart Tracer DDR3-1600 |
| Drives | Kingston SSDNow V+ 100 64GB SSD |
| CPU Cooler | SilverStone NT07-1156 with Cooler Master ThermalFusion 400 |
| Power Supply | SilverStone Strider Plus 750W 80 Plus Silver |
Each case is tested with just the Core i3's integrated graphics as well as with a discrete graphics card. The system is powered on and left idle for fifteen minutes, the thermal and acoustic results recorded, and then stressed by running four threads (three with a dedicated GPU) in Prime95 (in-place large FFTs) on the CPU, and OC Scanner (maximum load) is run when the dedicated GPU is installed. At the end of fiteen minutes, thermal and acoustic results are recorded. If the enclosure has a fan controller, these tests are repeated for each setting. Ambient temperature is also measured after the fifteen idle minutes but before the stress test and used to calculate the final reported results.
We try to maintain an ambient testing temperature of between 22C and 24C. Non-thermal test results aren't going to be directly comparable to the finest decimal point, but should be roughly comparable and give a broader idea of how the enclosure performs.
Thank You!
Before moving on, we'd like to thank the following vendors for providing us with the hardware used in our testbed.
- Thank you to Puget Systems for providing us with the Intel Core i3-2120.
- Thank you to Zotac for providing us with the Z68ITX-A-E motherboard and GeForce GTS 450 Eco.
- Thank you to Crucial for providing us with the Ballistix Smart Tracer memory.
- Thank you to Kingston for providing us with the SSDNow V+ 100 SSD.
- And thank you to SilverStone for providing us with the power supply and NT07-1156 heatsink/fan combo.
Facebook
Twitter
RSS
80 Comments
View All Comments
martyrant - Friday, November 23, 2012 - link
I'm a pretty big fan of Fractal Design cases; this looked quite promising (especially by the specs on the first page) until I got to the point where I read Dustin having issues getting the 560 Ti inside.I have maybe--MAYBE--used my optical drive a handful of times in the past 5 years. And almost all of those times I could have gotten away with using an alternative method (bootable USB, backed up ISOs, etc.) and am glad to see it omitted completely. Even in large desktop cases I'm starting to wish they would get rid of 5.25" bays completely and just give me 10-12+ internal 3.5" drive bays for massive RAID/fileserver setups (I have had my eye on the Fractal Design XL for a while now). Only reason I see myself using a 5.25" bay is for a hot swappable drive bay...and I don't use those often since I have a NAS that supports that. But I am amassing lots of old 640GB (have 4) and 500GB (have 4) drives and I use 4x128GB samsung 830s in raid0 as my boot...would be nice to RAID 5 the 640's and the 500s in a case though and maybe kill my NAS since my computer is almost always on anyway.
I do admit, optical drives in the work place have more of a use than at home for me.
lmcd - Friday, November 23, 2012 - link
I see potential with a single-slot 7750, personally, or a 160mm PSU that naturally doesn't have a lot of connectivityLadyKate - Sunday, November 25, 2012 - link
Love my job, since I've been bringing in $5600… I sit at home, music playing while I work in front of my new iMac that I got now that I'm making it online(Click on menu Home)http://goo.gl/ZXnvc
Grok42 - Friday, November 23, 2012 - link
I had the same reaction. It sounded like my dream case until I got to the part about it not handling the 560 Ti. I have a New Egg wishlist just begging me to hit the buy button with a Lian-Li QB25 case. I just can't do it because I'm on the fence about the case. The specs I have call for a 660 Ti GPU and a SILVERSTONE ST45SF-G PSU. The PSU used for the review is 7" deep while the one I've picked is less than 4" but I still worry about how much clearance there will be for the modular connectors.I'm still really excited by this case but it also appears to be difficult to purchase right now. I only saw it available through a few sources for $120+
londiste - Friday, November 23, 2012 - link
and yet, neither of you noticed that he is using a psu that is beyond fractal's spec. with a shorter psu, you'll fit a hell of a graphics card in there just fine.i know that the hardware dustin uses is same for comparison purposes but think about realistic power usage - 750w psu for an itx box? :)
Dustin Sklavos - Friday, November 23, 2012 - link
londiste is completely correct.I use standard hardware, but you WILL be able to fit a GTX 560 Ti (albeit probably barely) or even a 680 in this case if you put a smaller PSU in.
The problem then, though, is dealing with the cable spaghetti.
MonkeyPaw - Friday, November 23, 2012 - link
Seems like if more of these Mini-ITX cases start showing up and becoming standard, maybe manufacturers will start offering PSUs that work better. Smaller dimensions, shorter cables, etc. That, or these case makers need to start including a modest (realistic) PSU that works for the form factor. Personally, I don't think it needs more than ~400W, as running a space-heater GPU in such a cramped case is just asking for problems anyway.Guspaz - Friday, November 23, 2012 - link
You really don't need a super power supply in these things. The GeForce 680 has a TDP of 195W, the i7-3770 has a TDP of 77W. Those are the two most power hungry components, and you're only at 272 watts. Shuttle ships their mini ITX cases with a 500W PSU and certifies both of these components (actually up to 95W on the CPU, but I don't think any go that high yet).A good quality single-rail 500W PSU is probably enough for almost any Intel consumer desktop unless they're getting crazy with multi-GPU or insane numbers of hard drives (like my fileserver which has 15 hotswap bays :P).
Peoples' views of how big of a PSU they need has been skewed by the noname-brand garbage that floods the market. They buy an 600W PSU that fails if you push it beyond 300W and think they need an 800W PSU to replace it, when really they could have gone with a much lower wattage high quality PSU.
yyrkoon - Tuesday, November 27, 2012 - link
May as well call it 300W peak after adding a HDD, and optical drive. a Tad more with an SSD in addition.Problem is, any modern PSU to be the most efficient . It needs to be loaded at 50%. So we're again talking 600W for a PSU. If efficiency is not all that important, then you can futz around a bit but going under 500W will only be a problem with any power hungry GPU. e.g. the system stands a better chance of being less than rock solid stable. Now I can not speak for anyone else, but for me rock solid stability is a must in any build. However, i also would not require a beast of a graphics card either.
Lastly, not all PSU;s are created equal. So you're not necessarily guaranteed even 50% of the power total provided on the 12v rail. Assuming a single rail PSU. Most that I would trust being made by seasonic, while being branded by different companies. Antec comes to mind ( earthwatts 500 ) I've owned one now for 4-5 years and am perfectly happy with it. Granted, as stated above, i do not require a massive GPU.. Mostly i opt for mid range.
Now, if these case manufacturers would only isolate the PSU in a way where it draws in air from the outside while exhausting hot air out. Really a no-brainier, and as a hobbyist case moder it really isn't that hard But I digress. I suppose that would require more than 3 brain cells . . . Or really caring about what a system builder wants.
Metaluna - Friday, November 23, 2012 - link
Seems to me that what we need is for the industry to standardize on a set of connectors for modular PSUs. That would allow an aftermarket to develop for modular PSU cables of any length you need. Like in this case it looks like the main power connector only needs to be around 8" or so, if that. There are outfits that sell custom modular cables for select PSUs (e.g. Seasonic X-series) but they are ridiculously expensive.Oh, also regarding SFX supplies, I believe you can buy adapter plates that will allow them to mount on an ATX cutout, so that might help in this instance.